Mystery aftermarket part in my motorcycle

While doing the overhaul on my bike I discovered a mystery part attached underneath the driver seat.  It looks aftermarket as the screws holding it in place and the manner of attachment are very much not in they style of what Honda does.  My best guess is that it’s part of an old alarm system.  I am a little worried to hook it up to 12 volts to see what happens though.  The last time I did that to a mystery siren I had my ears ring for the next week!

IMG_9265

The unit says “Quorum” on the side. A little bit of googling shows that there is a company that manufactures alarms under that name. However I couldn’t find that company’s website or any photos of the siren.

IMG_9266

Looks to me like a siren.

IMG_9267

Wiring harness wasn’t connected to anything.

IMG_9268

It was mounted where my finger is pointing.  The two screw holes are visible just to the right of my finger.  The pink wire in the upper part of the frame near the red fuse holder has the same type of connectors as the wire on the unit.  That pink wire doesn’t go anywhere and was clipped.  No evidence of any modification to the rest of the bike’s electronics.

Am I missing a hose or three on my PC800?

NEWER UPDATE: The hose barb that dumped all the fuel out would connect to the evaporative emissions control on a California emissions-equipped bike. Page 5-6 in the service manual shows the way the hoses should be setup.

UPDATE: There were no hoses missing from my 49 state 1989 Pacific Coast.  I am told that it is supposed to be this way.  And the bike runs just fine.  Check out this thread and this post from the IPCRC for more information.

This morning while I was pulling the carbs off my bike I noticed what appears to be some missing hoses.  In fact, one of the bare hose barbs even dumped a bunch of fuel out when I pulled the carbs off.  Anyone know if there should be hoses on these barbs and where those hoses should go?  The bike has run just fine since I bought it 1000 miles ago.  Maybe I should just let sleeping dogs lay?

IMG_9257

My finger is pointing toward a bare hose barb.  It is open to the other hoses.  When I pulled the carbs off, a bunch of gas dumped out of this barb.  The hoses that branch off from this barb go to both carbs.  Update: that weird T thing is where all of the vacuum hoses come together on the carbs.

IMG_9261

Another view looking from the right side of the bike. There is also a barb with no hose on the plastic part where our trunk release and gas cap live.  It is visible on the lower front of that assembly (the left side of the photo).  It is in front of a brown hose with some condensation on it.  It is the same size as the barb on that multi-T thing which is at the same height in this photo and just to the right of center in the picture.

IMG_9263

This is looking from the right side of the bike.  My finger is pointing toward a little metal tube that comes off of the carb and goes into a rubber hose that appears to be broken off.  Is that supposed to be that way?  Maybe it’s just a plug or something?  The carbs are several blocks away (internet is out at the house) so I can’t look on the other carb to see if there is a similar setup or if it is unique to this carb.  Also can’t tell you if it is a plug or open.  Yeah, not to prepared this time 🙂

Taking off the carbs

This morning I took the carbs off my Pacific Coast.  The hardest parts of the operation were 1) figuring out how to get the throttle cables detached and 2) freeing the carbs from the engine.  Here are a few photos of the process.

IMG_9256

Air filter off. Rags are stuffed in the carbs so rain/dirt/etc doesn’t fall inside.

IMG_9269

The bike is positively looking like a parts bike!  Here the carbs are removed.  Rags are stuffed in the holes leading to the pistons and in the larger hoses that I had to disconnect.  Make sure to do this job in a well ventilated area.  Lots and lots of gas came out when I pulled off the carbs.